How Do You Refinish A Concrete Floor?

How can I make my concrete floor look good?

Painted Concrete Floors Epoxy treatments are often used to seal and repair a damaged concrete subfloor.

Epoxy is a strong material that can be poured into cracks and crevices to help level the surface.

But epoxy also is available in a variety of colors, allowing you to create unique hues and designs on your floor..

How do you refurbish a concrete floor?

How to refinish concrete floorsPrepare & Repair. Etch, grind, or shot blast the concrete surface to make it porous. … Clean & Prime. Mop and let the concrete slab thoroughly dry. … Mix Product. … Apply Overlay. … Add Patterns & Texture. … Cure & Seal.

How do you fix an old concrete floor?

Use a hammer and a cold chisel to level the bottom of the hole and undercut its sides slightly so the patch can’t pop loose. … Brush on a concrete bonding liquid, … Mix the concrete with water and scoop some into the hole. … To burnish the surface very smooth, use a steel trowel (shown) on the final few passes.

Can you put a thin layer of concrete over concrete?

Yes, you may pour a concrete pad overlay over an existing slab. You need to consider the added height and weight of the overlay on the existing structure. Overlays may include polymers, portland cement concrete, or epoxies.

What kind of paint do you use on concrete floors?

Epoxy paint(Epoxy paint is the best choice for floors, which take a lot of abuse. You’ll get the most durable results from epoxy, and it will hold up better over time than latex paint.) Be sure that both the primer and paint are suitable for the location of your floor, whether it’s an interior or exterior surface.

Is it better to stain or paint concrete floors?

Floor and concrete stains are usually easier to apply than paints, but they require more frequent reapplication to keep looking fresh. Rather than coating the floor in one entire color, concrete stains create a pigmented, marbled effect.

Can old concrete be resurfaced?

RE-CAP™ Concrete Resurfacer will renew your old, worn concrete driveways, sidewalks and patios at a fraction of the cost to tear out and replace old concrete slabs.

How hard is it to polish concrete floors?

Polishing concrete is a relatively straightforward process, and the long-term maintenance requirements are minimal. The process of polishing concrete is fairly straightforward, and it begins with floor preparation. Any coating or grime that is already on the floor must be removed, and existing cracks should be filled.

Can I polish my existing concrete floor?

Almost any structurally sound concrete floor, whether new or old, can be polished. However there are some exceptions, for example with new floors no special mix design is required to achieve good results – although the floor should be in place at least 28 days before polishing begins to ensure adequate curing.

Is stained concrete cheaper than wood floors?

In general, a tight budget will find concrete floors more budget-friendly, but it depends on the design and finish of the concrete floor. … Wood stains have come a long way and making a cheaper wood imitate the color of a more expensive species is a good way to control the budget.

How much does it cost to refinish a concrete floor?

For a concrete floor with a basic finish, you can expect to pay $2 to $12 per square foot. If you have an existing concrete slab that’s ready for staining, polishing, or application of a decorative coating or overlay, most decorative concrete floor installations can be quite cost-effective.

How do you refinish a concrete basement floor?

Introduction. Wash the Floor. … Sand and Vacuum the Floor. Sand off any old paint or any other uneven areas. … Fill Cracks and Holes. If the surface of your floor is cracked or rough, mix concrete patch compound, following package directions. … Apply Primer. … Apply Epoxy Paint. … Apply Masonry Sealer.

What is the best finish for concrete floors?

Top Concrete Finishing OptionsAcid Stain. An acid stain for concrete floor has a very bold look, recognizable by its mottled appearance and highly variegated finish. … Water-Based Stain. … Fast Stain. … Acrylic Sealer. … Standard Epoxy. … Metallic Epoxy. … Terrazzo or Granite Epoxy. … Quartz Sand Epoxy.

Can I sand concrete?

The good news is that concrete can be sanded with relative ease when the proper equipment is used, such as a good concrete sandpaper (made using diamond instead of sand). There are also three different types of sanded finish you can achieve, depending upon the tools and amount of removed material.

Can crumbling concrete be repaired?

The Cure for Crumbling Concrete Steps As long as the steps are structurally sound—meaning, they’re not spalling, flaking, or broken all the way through—you can repair most surface issues. … If your patch is thicker, build the vinyl concrete patcher up in ¼ inch applications.